high-efficiency pva plasticizer types

plasticizer - an overview | sciencedirect topics

Plasticizer - an overview | ScienceDirect Topics

The functional classifications are either primary or secondary. Plasticizers are used to convert PVC, a rigid plastic, into a soft, flexible, and elastic material. A plasticizer that is compatible with PVC and exhibits low volatility, good permanence, and high efficiency is referred to as a primary plasticizer.

Get Inquiry
plasticizers for pvc | polynt

Plasticizers for PVC | POLYNT

Models and types of PVC plasticizers Nowadays there are hundreds of different types of plasticizers, but not all are produced and used at a commercial level. Research in the field of synthesis of these organic compounds is constantly evolving, given the importance of their use in many construction and world trade fields.

Get Inquiry
plasticizer - an overview | sciencedirect topics

Plasticizer - an overview | ScienceDirect Topics

Plasticizers may comprise 15–50% of a PVC formulation. By changing type and amount of plasticizer, properties can be tailored to requirements. Increasing plasticizer concentration increases flexibility, decreases tensile strength, and reduces hardness (e.g., Figure 1).

Get Inquiry
bio-based plasticizer products | acs technical products

Bio-Based Plasticizer Products | ACS Technical Products

Plasticizers Bio-Based / Non-Migratory. ACS Technical Products produces a range of bio-based plasticizers to suit a variety of applications—from low to high molecular weight—that are engineered to deliver a variety of performance properties.

Get Inquiry
plasticizer

Plasticizer

Europe's and Global Plasticiser Use by type 2017. In North America the 2017 volume was ~1.01 million metric tonnes and in Europe the figure was 1.35 million metric tonnes, split between various end-use applications with a chemical type trend moving to higher molecular weight (HMW) orthophthalates and alternative types following regulatory issues concerning lower molecular weight (LMW ...

Get Inquiry
plasticizers in paint & coatings: uses, types and selection

Plasticizers in Paint & Coatings: Uses, Types and Selection

DOP or DnOP is light-colored, low volatility & odorless liquid. It was the most commonly used all-purpose plasticizer, although mainly used for polyvinyl chloride (PVC) resins. It is insoluble in water & has a low viscosity of 56 mPa.s at 25°C. DOP features: Good stability to heat and ultraviolet light; Broad range of compatibility, and

Get Inquiry
venting for high efficiency gas furnaces - part 1 materials

Venting for High efficiency Gas Furnaces - Part 1 Materials

There exist many, but mainly three types of plastic are commonly used for high-efficiency appliance venting: ABS, PVC, CPVC. ABS (Acrylonitrile butadiene styrene, if you must know) is the cheapest solution but it is often too flexible and susceptible to joint leaks and even cracks due to expansion/contraction/softening of the material with ...

Get Inquiry
plastic vent pipes for high-efficiency condensing furnaces

Plastic Vent Pipes for High-Efficiency Condensing Furnaces

Some high-efficiency furnaces also include a plastic pipe for intake area, and all types use a third plastic pipe to drain away the corrosive condensation resulting from the combustion process. Because there are no universal standards for exhaust and intake pipes on high-efficiency furnaces, there is a lack of clarity and accountability over ...

Get Inquiry
aqueous processing of sic green sheets ii: binder and plasticizer

Aqueous processing of SiC green sheets II: Binder and plasticizer

PVA.19 However, addition of plasticizer may result in the decrease in tape strength. It is essential that the relative concentration of the bind–plasticizer system must be se-lected and adjusted properly. Drying in aqueous tape casting process was studied by Briscoe et al.20 The drying behavior was similar to that

Get Inquiry
polyvinyl chloride

Polyvinyl chloride

PVC compounds can be created with a very wide range of physical and chemical properties based on the types and amounts of plasticizers and other additives used. Additional selection criteria include their compatibility with the polymer, volatility levels, cost, chemical resistance, flammability and processing characteristics.

Get Inquiry

Company Reviews